返回 发新帖回复
嗯嗯      

1904

主题

14

好友

6786

积分

版主

Rank: 7Rank: 7Rank: 7

发表于 2013-5-14 10:10:00 |显示全部楼层


目录

目 录............................................................................................................I

前 言.........................................................................................................IV

第一章 系统结构概述................................................................................1

1.1 概述....................................................................................................................1
1.2 菜单栏................................................................................................................2
1.3 图标栏................................................................................................................3
1.4 显示选项..........................................................................................................11
1.5 功能的优先级..................................................................................................12
1.6 控制窗口及控制选项窗口..............................................................................13
1.7 文件格式..........................................................................................................13
1.8 配置文件..........................................................................................................13

第二章 开始使用.........................................................................................16

2.1 从D3PLOT 文件开始使用.............................................................................16
2.2 软硬件系统需求..............................................................................................17

第三章 文件管理.........................................................................................18

3.1 打开文件..........................................................................................................18
3.2 导入文件..........................................................................................................19
3.3 导出文件..........................................................................................................20
3.4 拷贝到剪贴板..................................................................................................20
3.5 打印..................................................................................................................21
3.6 退出..................................................................................................................23

第四章 编辑菜单.........................................................................................24

4.1 创建线..........................................................................................................24
4.2 删除线..........................................................................................................26
4.3 标记/箭头.....................................................................................................26
4.4 旋转光源......................................................................................................27
4.5 光源特性......................................................................................................27
4.6 颜色表..........................................................................................................30
4.7 零件属性......................................................................................................31
4.8 用户自定义视角..........................................................................................38
4.9 背景颜色......................................................................................................39
第五章 工具箱...........................................................................................41
5.1 截面剖切..........................................................................................................42
5.2 运动约束..........................................................................................................51
5.3 沿XYZ轴镜像结果.........................................................................................52
5.4 定义活动窗口..................................................................................................54
5.5 定义节点轨迹..................................................................................................55
5.6 零件等值线结果历史曲线..............................................................................56
5.7 节点等值线结果历史曲线..............................................................................58
5.8 单元等值线结果历史曲线..............................................................................58
5.9 模型摘要..........................................................................................................59

第六章 选项...............................................................................................61

6.1 在图形区显示坐标轴的开关........................................................................61
6.2 在图形区显示标题的开关............................................................................61
6.3 在图形区显示图标的开关............................................................................61
6.4 在图形区显示图标的开关............................................................................62
6.5 模型法向颜色显示开关................................................................................62
6.6 显示单元方向的开关....................................................................................63
6.7 活性云图范围................................................................................................63
6.8 定义绕转中心................................................................................................64
第七章 后处理.........................................................................................65

7.1 变形................................................................................................................66
7.2 等值线............................................................................................................70
7.3 矢量................................................................................................................76
7.4 成形极限图....................................................................................................79
7.5 厚度................................................................................................................83
7.6 最大和最小主应变........................................................................................86
7.7 面内应变........................................................................................................87
7.8 坯料与工具间的距离....................................................................................89
7.9 圆栅格............................................................................................................91
7.10 滑移标记........................................................................................................93
7.11 坯料轮廓........................................................................................................95
7.12 材料流动........................................................................................................97
7.13 缺陷检查........................................................................................................99

第八章 曲线图.............................................................................................68

8.1 开始操作..........................................................................................................68
8.2 载入曲线表数据文件......................................................................................69
8.3 曲线表控制窗口..............................................................................................80
8.4 曲线操作..........................................................................................................82

附录 A 硬件和软件要求............................................................................99

后 记.........................................................................................................101

Dynaform后处理用户手册




本帖子中包含更多资源

您需要 登录 才可以下载或查看

来冒个泡!心情大好!...
发表于 2013-12-11 19:59:03 |显示全部楼层



哈哈哈 万变不离其宗  
回复

使用道具 举报

返回 发新帖 回复
您需要登录后才可以回帖 登录 | 注册

Powered by e-works © 2002-2012 中国制造业信息化门户网 版权所有
回顶部